ah101 - g medium power, high linearity amplifier datasheet: rev b 0 8 - 12 - 13 - 1 of 7 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.c om applications ? mobile infrastructure ? catv / dbs ? defense / homeland security ah101 sot - 89 package functional block diagram rf in gnd rf out gnd 1 2 3 4 ordering information part no. description ah101 - g med. power high linearity amplifier standard t/r size = 10 00 piece s on a 7 reel pin configuration pin no. label 1 rf in 3 rf out 2, 4 g nd general description the ah101 - g is a medium power gain block that offers excellent dynamic range in a low - cost surface mount package. the combination of a single supply voltage and an internally matched device makes it ideal for both narrow and broadband applications. only dc blocking and bypass capacitors as well as an rf choke are required for operation. superior thermal design allows the product to achieve +46 dbm ip 3 performance at a mounting temperature of +85c with an associated mttf of greater than 1000 years. th is broadband amplifier uses a high reliability gaas mesfet technology and is targeted for applications where high linearity is required . the ah101 - g i s available in the environmentally - friendly green/rohs - compliant sot - 89 package. product features ? 50 C 1500 mhz ? +47 dbm output ip3 ? 13.5 db gain ? +26.5 dbm p1db ? mttf > 1000 years ? internally matched ? single +9 v supply ? lead - free/rohs - compliant sot - 89 p ackage not recommended for new designs recomme nded replacement part: tqp7m9102
ah101 - g medium power, high linearity amplifier datasheet: rev b 0 8 - 12 - 13 - 2 of 7 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.c om recommended operating conditions parameter min typ max units supply voltage (v dd ) 7 9 10 v t case ? 40 +85 c tj for >10 6 hours mttf + 1 6 0 c electrical specifications are measured at specified test conditions. specifications are not gua ranteed over all recommended operating conditions. absolute maximum ratings parameter rating storage temperature ? 55 to 150c rf input power, cw, 50, t=25 c + 18 dbm supply voltage (v dd ) + 11 v operation of th is device outside the parameter range s g iven above may cause permanent damage. electrical specifications test conditions unless otherwise noted: v dd =+ 9 v, temp= +25c, 50 system. parameter conditions min typ max units operational frequency range 50 1500 mhz test frequency 800 mhz gain 12 13.5 16 db input return loss 20 db output return loss 15 db output p1db +26.5 dbm output ip3 pout = + 8 dbm/tone, ?f = 1 0 mhz +43 +47 dbm noise figure 3.5 db current, i dd 170 200 230 ma thermal resistance, jc junction to backside ground paddle 25 c/w s - parameters test conditions: v dd = + 9 v, i dd = 200 ma (typ.), t= +25 c, unmatched 50 ohm system, calibrated to device leads freq ( m hz) s11 (db) s11 (ang) s21 (db) s21 (ang) s12 (db) s12 (ang) s22 (db) s22 (ang) 50 - 18. 92 - 60.71 13.78 168.24 - 19.25 4.11 - 14.51 - 160.07 100 - 22.31 - 52.06 13.63 169.87 - 19.13 0.17 - 14.86 - 177.29 200 - 23.85 - 47.09 13.50 166.42 - 19.17 - 5.09 - 15.22 164.61 400 - 23.32 - 62.31 13.48 157.06 - 19.28 - 12.63 - 14.83 140.14 600 - 21.73 - 77.34 13.32 146 .40 - 19.36 - 19.07 - 14.55 118.64 800 - 20.76 - 90.04 13.19 135.74 - 19.47 - 25.94 - 14.02 97.71 1000 - 19.65 - 105.39 13.05 124.67 - 19.74 - 33.10 - 13.40 80.17 1200 - 18.62 - 121.62 12.94 114.96 - 20.07 - 39.77 - 12.95 63.09 1400 - 17.32 - 131.81 12.76 104.01 - 20.36 - 4 5.37 - 12.44 47.65 1600 - 16.53 - 141.33 12.55 93.98 - 20.44 - 53.24 - 12.02 31.14
ah101 - g medium power, high linearity amplifier datasheet: rev b 0 8 - 12 - 13 - 3 of 7 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.c om typical performance ? 50 - 1500 mhz test conditions unless otherwise noted: v dd =+9 v, i dd =200 ma (typ.), temp= +25c parameter typical value units frequency 50 450 900 1500 mhz gain 13.6 13.8 13.5 12.7 db input return loss 23 27 21 14 db output return loss 8 14 18 16 d b output p1db +26.1 +26.5 +26.5 +25 dbm ouput ip3 ( pout= +8 dbm/tone, f= 10 mhz ) +45 +47 +47 +47 dbm output ip2 +63 +63 +60 +59 dbm noise f igure 4.4 3.4 3.6 4.2 db performance plots ? 50 - 1500 mhz test conditions unless otherwise noted: v dd =+5v, i dd =85 ma (typ.), temp= +25c
ah101 - g medium power, high linearity amplifier datasheet: rev b 0 8 - 12 - 13 - 4 of 7 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.c om ah101 - pcb evaluation board ( 50? 150 0 mhz ) c1 c3 l1 c2 j4 j3 u1 r1 u1 ah101-g j2 rf output j4 gnd j3 v dd 1 2,4 3 j1 rf input l1 470 nh 0805 r1 0 : c2 0.018 uf c1 0.018 uf c3 0.018 uf vcc notes: 1. see evaluation board pcb information for material and stack -up. 2. r 1 (0 mxpshupdehuhsodfhglwfrsshuwudfhlqwhwdujhwdssolfdwlrqodrxw 3. al l components are 0603 size unless stated on the schematic. 4. the amplifier should be connected directly to a +9 v regulator; no dropping resistor is required. 5. if no dc signal is present at the input (pin 1), c1 can be removed. the gate (input pin) is intern ally grounded in the amplifier . 6. for higher frequencies of operation, use a lower value l2 inductor. performance plots ? ah101 - pcb test conditions unless otherwise noted: v dd =+ 9 v, i dd =200 ma (typ.), temp= +25c
ah101 - g medium power, high linearity amplifier datasheet: rev b 0 8 - 12 - 13 - 5 of 7 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.c om pin configuration and description rf in gnd rf out gnd 1 2 3 4 pin no. label description 1 rf in rf input, matched to 50 ohms. external dc block is r equired. 3 rf out rf output / dc supply, matched to 50 ohms. external dc block , bias choke required. 2, 4 g nd backside paddle. multiple vias should be employed to minimize inductance and thermal resistance; see pcb mounting pattern in mechanical inform ation section. evaluation board pcb information triquint pcb 1075825 material and stack - up 1 oz. cu bottom layer nelco n-4000-13 nelco n-4000-13 r =3.9 typ. nelco n-4000-13 1 oz. cu top layer 1 oz. cu inner layer 1 oz. cu inner layer 0.014" 0.014" 0.062" 0.006" finished board thickness 50 ohm line dimensions: width = 0.029, spacing = 0.035
ah101 - g medium power, high linearity amplifier datasheet: rev b 0 8 - 12 - 13 - 6 of 7 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.c om mechanical information package marking and dimensions marking: part number C 101g lot co de C xxxx- x n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. dimension and tolerance formats conform to asme y14.4m - 1994. 3. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp -012. pcb mounting pattern notes : 1. ground / thermal vias are critical for the proper performance of this device. vias should use a .35mm (#80 / .0135) diamete r drill and have a final plated thru diameter of .25 mm (.010). 2. add as much copper as possible to inner and outer layers n ear the part to ensure optimal thermal performance. 3. mounting screws can be added near the part to fasten the board to a heatsink. ensure that the ground / thermal via region contacts the heatsink. 4. do not put solder mask on the backside of the pc boa rd in the region where the board contacts the heatsink. 5. rf trace width depends upon the pc board material and construction. 6. use 1 oz. copper minimum.
ah101 - g medium power, high linearity amplifier datasheet: rev b 0 8 - 12 - 13 - 7 of 7 - disclaimer: subject to change without notice ? 2013 triquint www.triquint.c om product compliance information esd sensitivity ratings caution! esd - sensitive device esd rating: class 1 c value: passes 1000 v min. test: human body model (hbm) standard: jedec standard jesd22 - a114 esd rating: class i v value: passes 9 test: charged device model (cdm) standard: jedec standard jesd22 - c101 solderability compatibl e with both lead - free (260 c max. reflow temperature) and tin/lead (245 c max. reflow temperature) soldering processes. contact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of cert ain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating msl rating : level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 contact information for the latest specifications, additional product information, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@triquint.com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@triquint.com important notice the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. tr iquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability whatsoever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant informati on before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with reg ard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure wou ld reasonably be expected to cause severe personal injury or death.
|
